MOXA Media Konverter: Fiber Optic (Glasfaser) nach RS232/RS422/485

RS232 nach RS422/485 Konverter

TCF-142M

Preis € Restbestand!

The TCF-142 Series serial to fiber converter is equipped with a multiple interface circuit that can handle conversion between either RS-232 or RS-422/485 serial interfaces, and multi-mode or single-mode optical fiber. TCF-142 converters are used to extend serial transmission distance up to 2 km (TCF-142-M multi-mode fiber) or up to 20 km (TCF-142-S single-mode fiber).

Technische Dokumentation als PDF-Datei

TCF-142-M/-S/-T

Preis €

The TCF-142 media converter is equipped with a multiple interface circuit that can handle RS-232 or RS-422/485 serial interfaces and multi-mode or single-mode fiber. TCF-142 converters are used to extend serial transmission up to 5 km (TCF-142-M with multi-mode fiber) or up to 40 km (TCF-142-S with single-mode fiber). The TCF-142 can be configured to convert either RS-232 signals, or RS-422/485 signals, but not both at the same time.

# “Ring” and “Point-to-Point” transmission
# Extends RS-232/422/485 transmission up to:
    * 40 km with single-mode—TCF-142-S
    * 5 km with multi-mode—TCF-142-M
# Compact size
# Decreases signal interference
# Protects against electrical interference and chemical corrosion
# Supports baudrates of 50 bps to 921.6 Kbps
# Wide temperature models available (-40 to 75°C)

Automatic Baudrate Detection

The TCF-142 can automatically detect the serial baudrate. This is an extremely convenient feature. Even if a device€™s baudrate is changed, the signal will still be transmitted through the media converter without any data loss.

The TCF-142 can be used to connect serial devices to a fiber ring. To form the ring, connect the Tx port of one TCF-142 to the Rx port of a neighboring converter. Once the ring is set up, simply use the DIP switches to configure the TCF-142 converters for “ring mode.� When one node transmits a signal, the signal travels around the ring until it returns back to the transmitting unit, which then blocks the signal. With the TCF-142, you can set up fiber rings that have a total circumference of up to 100 km.
 

Technische Dokumentation als PDF-Datei

TCF-142-RM

Preis € neu

The TCF-142-RM series of serial-to-fiber converters are slide-in modules that work with the TRC-190 chassis. The modules convert from the RS-232, RS-422, or RS-485 signal to a fiber optic signal.

Features:

› Extend RS-232/422/485 transmission up to:
  • 40 km with single mode
  • 5 km with multi-mode
› 1K or 150K ohm adjustable pull high/low resistor
› “Ring"  and "Point-to-Point" transmission supported

Das 19” Racksystem TRC-190 für TCF-142-RM siehe unten 

Technische Dokumentation als PDF-Datei

TRC-190

Preis €

The TRC-190 series provides 19 slots for media converter modules such as the TCF-142-RM series. A TRC-190 chassis comes with one AC or DC power input, with an optional redundant power expansion module available for greater reliability. The TRC-190 series' power input module supports the hot-swap feature. 19-inch chassis for rackmount use


› 19-inch chassis for rackmount use
› 19 slots for high density applications
› Supports hot-swap and dual power input with redundancy
› Fan-less design chassis for reducing repair time

Technische Dokumentation als PDF-Datei

TCF-90

Preis €

The TCF-90 is a compact media converter that transmits RS-232 signals over optical fiber. Power is derived from either the serial port or an external power source. The TCF-90 extends RS-232 transmission up to 5 km with multi-mode fiber, or up to 40 km with single-mode fiber. A pair of TCF-90 converters can be used to connect two RS-232 devices with optical fiber in full duplex mode. The optical fiber isolates the data signals from dangerous increases in ground potential, ground loops, and electrical EMI/RFI noise, and enhances data security by eliminating the harmful effects of RF radiation and susceptibility to electromagnetic radiation.

# Use either external power or power over serial
# Extends RS-232 transmission up to:

    * 40 km with single-mode—TCF-90-S
    * 5 km with multi-mode—TCF-90-M

# Reduces signal interference
# Protects against electrical interference or chemical corrosion
# 15 KV ESD protection for serial signals
# Baudrates up to 921.6 Kbps

Technische Dokumentation als PDF-Datei

TCF-1150

Preis € neu

The ICF-1150 series support 2 serial ports, with a D-sub connector for RS-232 communication and a removable terminal block for RS-422 or RS-485 communication. The 3 ports (2 serial ports and one fiber port) are completely independent. When an ICF-1150 converter receives data from any one port, it will send the data out through the other 2 ports. For example, once the ICF-1150 converter receives a command from the remote master through the fiber port, it will convert the signal and send the command through the RS-232 and RS-422/485 ports at the same time. If the user is monitoring a system running on an RS-485 network, there is no need to use an additional RS-232 to RS-485 converter to connect the laptop computer's serial port to the RS-485 bus.

ۼ RS-232, fiber, and RS-422/485 3-way communication
ۼ Rotary switch to change the pull high/low resistor value
ۼ Extend RS-232/422/485 transmission up to:
  · 40 km with single-mode
  · 5 km with multi-mode
ۼ 3-way Galvanic Isolation (for "I" model only)
€º - 40 to 85°C wide temperature models available
ۼ Class I, Div. II certification (Pending)

Technische Dokumentation als PDF-Datei